=======================================
- Alcorn McBride Inc.
-
- LightCuePro
---------------------------------------
Installation Instructions

1. Copy OS.NEW to the Compact Flash card. (Rename to OS.nEW if needed)
   
2. Reset unit by turning it off, and then on again. 

3. Wait for Update to complete.  You will see "Firmware Update Complete!" on the screen when finished.

Note: You can alternatively use the menu in Winscript under Help-->Update Firmware to download and update the firmware.

NOTE: 	When the update is complete, the OS.NEW file will be renamed to OS.SAV so that the update does not
	repeat when the hardware is powered-up again.  If you want to use a single flash card to update
	multiple units (for example, an entire Binloop cage), you can change the name of the OS.NEW file
	to FACTORY.NEW.  The FACTORY.NEW file will perform an update just like OS.NEW, only it will not be
	renamed at the end of the update process.  This means that after an update, you can remove the 
	flash card from the product and insert it into another product to perform another update.  

NOTE: 	Updating the firmware may cause the LightCuePro to reset to it's factory default network settings.  Make sure that you remember or write down these settings before updating your LightCuePro. (IP Address, username, password, etc)
	

----------------------------------------
If you have any questions regarding any items listed in this document, please contact support@alcorn.com.


*****************************************
*					*
*	   Release Notes		*
*					*
*****************************************
*************************
*    Version 1.21	*
*************************
- Corrected issue with traffic sent to UDP port 0

*************************
*    Version 1.20	*
*************************
- Added Cues to Web Scheduler

*************************
*    Version 1.19	*
*************************
- Added "SG" command to allow self-gen SMPTE time to be set

*************************
*    Version 1.18	*
*************************
- Fixed "Clear" command when using button presses or inputs

*************************
*    Version 1.17	*
*************************
- Added "command" tag to allow loop plays using scheduler
- Work done on "at"
- Fixed legacy mode rear inputs so a "1" plays file "dmx00002.dmx"

*************************
*    Version 1.16	*
*************************
- Allowed Pile-On chase play to leave other files running
- Allowed 'End time' to be present in schedule without an 'End date'

*************************
*    Version 1.15	*
*************************
- Added Send Strings for Schedule Files
- Fixed incorrect reporting of hardware type

*************************
*    Version 1.14	*
*************************
- fix for file system ftp over files

*************************
*    Version 1.13	*
*************************
- fix for Ethernet A & B used at the same time
- fix for 25fps timecode

*************************
*    Version 1.12	*
*************************
- update for rear panel strapping on boot

*************************
*    Version 1.11	*
*************************
- fixed ip not sticking

*************************
*    Version 1.10	*
*************************
-Updated timezones for .5 hour timezones

*************************
*    Version 1.09	*
*************************
-Added SMPTE protect against invalid values

*************************
*    Version 1.08	*
*************************
-Fixed invalid DMX values on record

*************************
*    Version 1.07	*
*************************
-Updated SMPTE file to ignore DMX when out of range of file

*************************
*    Version 1.06	*
*************************
-Fixed UDP not always responding to messages

*************************
*    Version 1.05	*
*************************
-Fixed possible boot lockup after file load
-Fixed SMPTE "jump" with frequent serial requests

*************************
*    Version 1.04	*
*************************
-Added upload/download of non os files
-Fixed cue name bug

*************************
*    Version 1.03	*
*************************
Skipped to match LightCueManager version

*************************
*    Version 1.02	*
*************************
-Additional LightCueManager Functionality

*************************
*    Version 1.01	*
*************************
-Added Cuenames functionality
-Added Live Mode for LightCueManager

*************************
*    Version 1.00	*
*************************